Blog
In this blog, ETU-LINK will focus on introducing the type and transmission distance of the Gigabit single-mode SFP BIDI SC connector optical module. This series of optical modules can not only support 2km, 3km, 10km, 20km, 40km, 60km, 80km, 120km transmission distances, but also have commercial (0℃-70℃) and industrial (-40℃-85℃) optional temperature ranges. In order to facilit...
At present, MPO patch cord is widely used in high-speed and high-density data center wiring, and its quality determines the stability and sustainability of the whole data center network. So what factors should we consider when choosing MPO patch cord? Today ETU-LINK will introduce the Purchasing Guide of MPO patch cord. 1. Choose a patch cord with a small insertio...
Cisco 550X series switches are mainly used for the establishment of 10G network for small and medium-sized enterprises. ETU-Link will introduce the optical module solution of Cisco 550X series switches. Cisco 550X is configured with Ethernet SFP+ slot, which can support 10 Gigabit and Gigabit network transmission rates. The SFP+ slot can select the optical module with the corresponding...
DAC high-speed cable is a low-cost and short-distance connection solution for data center equipment. It consists of a cable and optical fiber transceiver devices at both ends of the cable. Because of the high cost performance, the interconnection application between short-distance network equipment is widely welcomed. At present, there are many specifications of DAC high-speed cables on the market...
The optical module is an important component of the optical fiber communication system, which is used to realize the transmission and reception of optical signals. The speed of the optical module used in the data center ranges from 1G before 2010 to the commonly used 10G and 40G now. Since most of the equipment distance in medium and large data centers is within 500 meters, the interconnection bet...
一. Introduction to MPO Patch cord The MPO fiber optic patch cord is composed of a hot-swappable MPO connector and a multi-mode/single-mode fiber optic cable. The MPO optical fiber connector includes optical fiber, sheath, coupling components, metal ring, pin, dust cap, etc., and the pin part is divided into two forms: male and female. The male connector has two PIN pins, while the female connector...
This blog ETU-LINK takes everyone to understand the difference between optical fiber, copper cable and twisted pair. First of all, let’s understand the twisted pair. The twisted pair is made up of multiple groups of insulated copper wires intertwined. The internal medium of the twisted-pair cable is also copper wire, and the internal transmission is an electrical signal. According to the principle...
In this article, ETU-Link will explain to you what causes the high temperature of the optical module and how to solve it. Generally speaking, a brand-new optical module will not have any major problems during short-term use. The optical module is a relatively sensitive optical device. When the operating temperature of the optical module is too high, it will cause problems s...
The Fibre Channel switch originated from the Fibre Channel protocol. On the fourth layer of the Fibre Channel protocol, the Fibre Channel-based SCSI protocol for storage, the IP protocol for the network, and the virtual interface (VI) protocol for clusters mapped to the network architecture are established. Fibre Channel switches provide Fibre Channel switching for high-bandwidth and low-latency d...
SAN refers to the regional storage network, which needs to be connected by optical fiber, and the operation mode of the SAN mainly depends on the hardware. The structure of the SAN allows any server to connect to any storage array so that the server can directly access the data it needs no matter where it is located. Due to the optical fiber interface, the SAN also has a higher bandwidth. The SAN ...
In this article, ETU-LINK will take everyone into the optical fiber cabling system, which is simply the transmission network in buildings and complexes. The integrated wiring system is a digital infrastructure built by intelligent offices, which can support integrated applications such as voice, data, graphics, and multimedia. The integrated optical fiber wiring system is divided into the followin...
The Internet cafe network system needs to have a high bandwidth and support a large amount of data transmission. Therefore, Internet cafes have higher requirements for network hardware. When designing the Internet cafe network, it is necessary to ensure a high-quality network transmission speed, and also consider future network upgrades and maintenance. Next, ETU-LINK will introduce network equipm...
Categories
New Blog
Tags
© Copyright: 2024 ETU-Link Technology CO ., LTD All Rights Reserved.
IPv6 network supported
Friendly Links:
易天官网